Local contractor in 73737

A service call to inspect a walk-in freezer revealed that the fan was not operating properly. We identified a grounded compressor that requires replacement. During our visit, we ensured to communicate our findings effectively, and the back door was accessible for our entry. Solutions for the freezer's issues were discussed to ensure it operates efficiently in the future.

A PAC unit in Fairview was not functioning properly as it had been off for a week and was blowing warm air. Upon inspection, we discovered that the compressor was experiencing a locked rotor, pulling 70 amps while attempting to start. To resolve the issue, we determined it was necessary to consider either repairing or replacing the compressor.

To prepare for the installation of a new HVAC system, we visited the site to take precise measurements and collect data. This included inspecting the designated 22x28 door opening to the attic to ensure a seamless installation process. We recorded all necessary details for the equipment replacement, setting the stage for an efficient and effective setup.

A malfunctioning HVAC unit prompted our visit to Fairview. We discovered that the system was low on refrigerant, specifically R410a. After cleaning the evaporator coil, we charged the unit with four pounds of refrigerant. We noted that the evaporator coil would need replacement for optimal performance moving forward.

A malfunctioning inverter board was identified in the HVAC system. To address this issue, we scheduled a job to replace the blown inverter board and restore the system’s functionality. This work is essential for maintaining efficient heating and cooling in the home. We look forward to ensuring optimal performance once the new component is installed.

A malfunctioning commercial refrigerator was causing products to freeze. We diagnosed the issue and found a faulty thermostat. After replacing the thermostat and adding 8 ounces of R134a refrigerant, the cooler returned to optimal functioning. Now, the refrigeration system is performing well, ensuring the customer’s products remain at the correct temperature.

A thorough preventative maintenance service was conducted for the HVAC system. We performed routine checks on electrical components, cleaned the condenser, and inspected the air filters and freon levels. The system is now functioning well, showing a 20-degree temperature difference, ensuring optimal performance for the summer season.

A malfunctioning air conditioning unit indicated that the air flow was not cooling effectively. We discovered a faulty condenser fan motor and contactor, which we promptly replaced. Additionally, we performed a thorough servicing of the unit for the summer, checking electrical components, air filters, freon levels, and washing the condenser coil. The system is now functioning well, achieving a 19-degree temperature difference.

A unit freezing up indicated that immediate attention was necessary. We serviced the air conditioning system to ensure it operates efficiently for the summer. This included checking electrical components, air filters, and Freon levels, as well as cleaning both the condenser and evaporator coils. The AC is functioning well now, providing much-needed relief.

A malfunctioning mini split system at Fairview required immediate attention due to a leak suspected to be from the pump. We identified the faulty pump and rerouted the drain temporarily to the sink. This prompt action ensures that the heating system can be restored effectively, addressing the needs of the administrative office.

A malfunctioning air conditioning unit in Fairview prompted us to perform a thorough inspection and service. We discovered a faulty run capacitor, which we replaced with a new one. Additionally, we serviced the unit for the upcoming summer by checking electrical components, air filters, refrigerant levels, and cleaning the condenser coil. The system is now operating efficiently.

A compressor cycling issue was detected during our service call. Upon inspection, we identified a faulty board that needed replacement. We proceeded to recommend ordering a new board to restore optimal functioning of the HVAC system. The job was completed efficiently, ensuring the system will work reliably moving forward.

A scheduled service call involved performing maintenance on an HVAC unit. We checked electrical components, air filters, and freon levels, and also washed the condenser coils. We charged the unit with 5 lbs of R410a refrigerant to ensure optimal performance throughout the summer months in Fairview.

A malfunctioning HVAC system required our attention as the compressor was not engaging and drawing an excessive 240 amps on startup. We performed a thorough examination to gather detailed information from both the indoor and outdoor units. This assessment will enable us to provide an accurate estimate for new equipment, ensuring the system is restored to optimal performance.

To provide a thorough residential estimate, we evaluated the existing HVAC system on June 10. We assessed its overall condition and functionality, ensuring that the proposed updates would meet the homeowner's needs effectively. Following our inspection, we compiled a detailed estimate outlining necessary installations and potential enhancements to ensure optimal comfort.

During our inspection of the HVAC system, we identified that the compressor was producing a loud noise due to the failure of the reed valves. We discussed possible solutions with the homeowner, including an estimate for both repairing the existing unit and replacing it with a new one. This assessment aimed to address the ongoing issues effectively.

To address a service call that involved HVAC repair, we dispatched our skilled technicians, Jordan and Joshua, to the Fairview area. We thoroughly evaluated the system and completed the necessary repairs, ensuring optimal performance. The job was executed efficiently, and we appreciate the opportunity to assist with your HVAC needs.

A welding shop's air conditioning system presented cooling issues, prompting us to investigate. Upon inspection, we discovered blown fuses in the main breaker box. We replaced the fuses and identified a faulty transformer. After installing a new 480v to 24v transformer, we tested the system, confirming it operated without problems.

A malfunctioning HVAC system led to our assessment of the unit, where we discovered faulty run and start capacitors. We installed new capacitors, enabling the compressor to operate again. However, it continued to shut down due to high amp draw, indicating the need for a new compressor and a hard start kit.

A malfunctioning air conditioning unit needed attention due to insufficient cooling. After diagnosing the issue, we found the compressor was not operating because of a weak capacitor. We installed new capacitors and serviced the AC system to ensure optimal performance for the summer months, running the system smoothly afterwards.

A unit was experiencing a leak, prompting us to perform a thorough inspection. We looked for any water leaks but found none at this time. To ensure efficient operation, we vacuumed out the drain pan and ran water through the line to verify that it was clear. This comprehensive service was completed in Fairview.

The air conditioning unit was not cooling properly, prompting a service call. Upon inspection, we discovered that the mini split was low on freon. We charged the unit with R410a, ensuring its optimal function. Additionally, we repaired the drain line using 3/4 inch PVC. The AC system is now operating effectively in Fairview.

A malfunctioning intake motor was reported, indicating issues with the HVAC system. We inspected the unit and discovered broken blower shaft brackets and a damaged squirrel cage. To address this, we will need to disassemble the entire system for either repair or replacement. This process will ensure the HVAC functions effectively again in Fairview.

A malfunctioning HVAC system was addressed at the Fairview property. We discovered a bad transformer and a shorted contactor. We replaced the faulty components with a new power transformer and a contactor, resulting in the system operating effectively. Additionally, we verified the freon levels, noting a temperature difference of 18 degrees, ensuring optimal performance.

A thorough inspection of the HVAC system revealed clogged filters and a dirty condenser coil. We cleaned the filters and the coil to ensure optimal performance. After completing the maintenance, we ran the system in both heating and cooling modes without any issues. Our focus is on keeping your home comfortable year-round.

A malfunctioning pilot light was causing intermittent issues with the Amsco 2-21 unit. We identified that the spark igniter was failing, which was responsible for the pilot light not staying lit. After servicing the unit, we cleaned the air ports, flame sensor, and ensured the filters were clear. The system was working properly when we completed the service call in Fairview.

The HVAC system required attention due to a slow-turning fan and weak airflow from the outdoor unit. Upon inspection, we found the unit operating in manual mode and not responding to its remote. We ordered a new remote control and left it at the customer's front porch for easy access.

A failing HVAC unit prompted us to perform an installation on the system. We ensured that all components were functioning correctly during our work. Moving forward, we identified that the vent pipe needed replacement to enhance the system's efficiency. The job is currently in progress, and we are dedicated to ensuring everything operates seamlessly.

A malfunctioning HVAC system prompted us to investigate the issue. We discovered that the compressor would not start, so we replaced the dead run capacitor with a turbo 200 xl. Additionally, we added refrigerant to improve the subcooling levels. We also found and replaced a collapsed 14-inch return air duct with 12 feet of new flex duct. The customer requested further duct work replacement, and we noted a need to check a frozen two-door freezer during our next visit.

A malfunctioning heating system prompted us to conduct a thorough service call. We identified a bad limit on the heat strips, which will require the purchase of a new heat strip kit. Additionally, we installed a new PTAC (Packaged Terminal Air Conditioner) unit to ensure efficient climate control. This work enhances the comfort and functionality of the HVAC system.